Publisher: NACE International Publish Date: 2015 Pages: 164 Language: English Format: PDF Document Scope This part of ANSI/NACE MR0175/ISO 15156 describes general principles and gives requirements and recommendations for the selection and qualification of metallic materials for service in equipment used in oil and gas production and in natural-gas sweetening plants in...
Publisher: API Publish Date: 2003 Pages: 34 Language: English Format: PDF Size: 930 Kb Document Scope 1 This RP covers required and recommended features of the following aspects of bottom loading and vapor recovery: a. The configuration and operation of 4-in. (101.6 mm) adapters for bottom loading. b. Tank vehicles equipped for bottom loading or vapor recovery. c. Secondary...
Publisher: API Publish Date: 2013 Pages: 34 Language: English Format: PDF Size: 497 Kb Document Scope This RP applies to all parts of a pipeline or pipeline facility including line pipe, pump station piping, terminal piping, compressor station piping, metering station piping, delivery station piping, regulator station piping, appurtenances connected to line pipe, appurtenances...
Publisher: API Publish Date: 2009 (Errata 2011) Pages: 78 Language: English Format: PDF Size: 858 Kb Document Scope 1.1 This recommended practice (RP) sets criteria for the design, construction, testing, operation, and maintenance of offshore steel pipelines utilized in the production, production support, or transportation of hydrocarbons; that is, the movement by pipeline of...
Publisher: API Publish Date: 2015 Pages: 78 Language: English Format: PDF Document Scope This recommended practice (RP) sets criteria for the design, construction, testing, operation, and maintenance of offshore steel pipelines utilized in the production, production support, or transportation of hydrocarbons; that is, the movement by pipeline of hydrocarbon liquids, gases, and...
Publisher: API Publish Date: 2007 Pages: 58 Language: English Format: PDF Size: 849 Kb Document Scope 1.1 PURPOSE This Recommended Practice (RP) focuses on the design and implementation of displays used for the display, monitoring, and control of information on pipeline Supervisory Control and Data Acquisition Systems (SCADA). The primary purpose is to document industry...
Publisher: API Publish Date: 2016 Pages: 144 Language: English Format: PDF Document Scope This recommended practice (RP) is applicable to any pipeline system used to transport hazardous liquid or natural gas, including those defined in U.S. Title 49 Code of Federal Regulations (CFR) Parts 195 and 192. This RP is specifically designed to provide the operator with a description...
Publisher: API Publish Date: 2009 Pages: 124 Language: English Format: PDF Size: 2 218 Kb Document Scope This International Standard provides procedures for the laboratory testing of both drilling fluid materials and drilling fluid physical, chemical and performance properties. It is applicable to both water-based and oil-based drilling fluids, as well as the base or make-up...
Publisher: API
Publish Date: 2015
Pages: 74
Language: English
Format: PDF
Size: 932 kB
Scope
This recommended practice (RP) presents recommendations for designing, installing, and testing a process safety
system for subsea applications. The basic concepts of subsea safety systems are discussed and protection methods
and requirements of the system are outlined.
For...
Publisher: API Publish Date: 2002 Pages: 36 Language: English Format: PDF Size: 320 Kb Document Scope This recommended practice provides guidelines for safely conducting welding, cutting or other hot work activities in refineries, gas plants, petrochemical plants and other facilities in the petroleum and petrochemical industries. It includes specific guidance to evaluate...
Publisher: API Publish Date: 2014 Pages: 162 Language: English Format: PDF Document Scope The purpose of this recommended practice is to provide guidelines for classifying locations Class I, Division 1 and Class I, Division 2 at petroleum facilities for the selection and installation of electrical equipment. Basic definitions given in the 2011 Edition of NFPA 70, National...
Publisher: API Publish Date: 2001 ( Reaffirmed 2015 ) Pages: 48 Language: English Format: PDF Size: 339 Kb Document Scope This recommended practice provides external fusion bonded epoxy coating of line pipe for use in transportation pipelines. The Recommended Practice is limited to the application of external coatings on pipe prior to installation. There may exist differences...
Publisher: API Publish Date: 2013 Pages: 18 Language: English Format: PDF Size: 184 Kb Document Scope This recommended practice (RP) may supplement the API equipment specifications for carbon and low alloy steel large cross section and critical components. The recommend practice described herein suggests the requirements for batch-type bath quench and water spray quench-type...
Publisher: API Publish Date: 2015 Pages: 124 Language: English Format: PDF PRODUCT NO. G16C02 Size: 2030 kB Scope This specification establishes the minimum requirements for the design and manufacture of the following types of new equipment: a) articulated choke and kill lines; b) choke and kill manifold buffer chamber; c) choke and kill manifold assembly; d) drilling choke...
Publisher: API Publish Date: 2011 Pages: 274 Language: English Format: PDF Size: 2 291 Kb Document Scope ( API Spec 17D is identical to ISO 13628 Part.4 ) This part of ISO 13628 provides specifications for subsea wellheads, mudline wellheads, drill-through mudline wellheads and both vertical and horizontal subsea trees. It specifies the associated tooling necessary to handle,...
Publisher: API
Publish Date: 2015
Pages: 120
Language: English
Format: PDF
Size: 3042 kB
Scope
This specification covers seamless, centrifugal cast, and welded alloy line pipe with improved corrosion resistant properties. The purpose of this specification is to provide standards for pipe with improved corrosion resistance suitable for use in conveying gas, water, and...
American Petroleum Institute, 2018. — 394 p. This specification identifies requirements and gives recommendations for the performance, dimensional and functional interchangeability, design, materials, testing, inspection, welding, marking, handling, storing, shipment, and purchasing of wellhead and tree equipment for use in the petroleum and natural gas industries.
This specification identifies requirements and gives recommendations for the performance, dimensional and functional interchangeability, design, materials, testing, inspection, welding, marking, handling, storing, shipment, and purchasing of wellhead and tree equipment for use in the petroleum and natural gas industries. This specification does not apply to field use or field...
Publisher: API Publish Date: 2015 Pages: 280 Language: English PRODUCT NO. C53007 Format: PDF Document Scope This standard specifies the requirements and gives recommendations for the procedures and design criteria used for calculating the required wall thickness of new tubes and associated component fittings for fired heaters for the petroleum, petrochemical, and natural gas...
Publisher: API Publish Date: 2014 Pages: 386 Language: English Format: PDF PRODUCT NO. C61708 Scope Covers the minimum requirements for axial compressors, single-shaft and integrally geared process centrifugal compressors, and expander-compressors for use in the petroleum, chemical, and gas industries services that handle air or gas. Part 1— General Requirements, contains...
Publisher: API Publish Date: 2014 Pages: 20 Language: English Format: PDF Document Scope This standard specifies the requirements and acceptance criteria (100 ppmv) for fugitive emission type testing of rising and rising-rotating stem valves equipped with packing previously tested in accordance with API 622. Packing shall be suitable for use at service temperatures –29 °C to...
Publisher: API Publish Date: 2016 Pages: 340 Language: English Format: PDF Document Scope This standard specifies requirements and gives recommendations for the design, materials, fabrication, inspection, testing, preparation for shipment, and erection of fired heaters, air preheaters (APHs), fans, and burners for general refinery service. This standard does not apply to the...
API, 2015. — 66 p. Product Number: C60209 This international standard specifies the requirements for a series of compact steel gate, globe and check valves for petroleum and natural gas industry applications.It is applicable to valves of: nominal pipe sizes NPS 1/4, NPS 3/8, NPS 1/2, NPS 3/4, NPS 1, NPS 1 1/4, NPS 1 1/2, NPS 2, NPS 2 1/2, NPS 3, and NPS 4; corresponding to...
Publisher: API Publish Date: 2016 Pages: 36 Language: English Format: PDF Document Scope Scope. This standard covers design, materials, face-to-face dimensions, pressure-temperature ratings, and examination, inspection and test requirements for gray iron, ductile iron, bronze, steel, nickel-based alloy, or special alloy butterfly valves.
Publisher: API Publish Date: 2016 Pages: 302 Language: English Format: PDF Document Scope This standard establishes minimum requirements for material, design, fabrication, erection, and inspection for vertical, cylindrical, aboveground, closed- and open-top, welded storage tanks in various sizes and capacities for internal pressures approximating atmospheric pressure (internal...
Publisher: API
Publish Date: 2006
Pages: 104
Language: English
Product Number: C67703
Covers the minimum requirements for general-purpose, enclosed, single,
and multistage gear units incorporating parallel shaft helical and right angle
spiral bevel gears for the petroleum, chemical, and gas industries. Gears
manufactured according to this standard shall be limited to the...
Publisher: API
Publish Date: 2014
Pages: 60
Language: English
Format: PDF
Size: 623 kB
Scope
This standard provides installation quality control procedures for monolithic refractory linings and may be used to supplement owner specifications. Materials, equipment, and personnel are qualified by the methods described, and applied refractory quality is closely monitored,...
Publisher: API Publish Date: 2015 Pages: 84 Language: English Format: PDF Document Scope The scope of this technical report is to provide design guidelines for oil and gas subsea equipment utilized in highpressure high-temperature (HPHT) environments (refer to 3.1.16). For the purpose of the technical report, HPHT environments are intended to be one or a combination of the...
Publisher: API Publish Date: 2015 PRODUCT NO. C938C03 Pages: 70 Language: English Format: PDF Size: 1363 kB Scope This report covers many of the lean, standard, super, and hyper grades of duplex stainless steels (DSSs) most commonly used within refineries. The definitions of these terms have not been firmly established by the industry, and vary between literature references and...
Publisher: ASME
Publish Date: 2004
Pages: 186
Language: English
Document Scope
This Guide covers recommended inspection and testing
procedures for electric and hydraulic elevators, escalators,
and moving walks required to conform to the
Safety Code for Elevators and Escalators, A17.1–1955
and later editions and The Safety Code for Existing
Elevators and...
Publisher: ASME Publish Date: 2016 Pages: 138 Language: English Format: PDF Document Scope This pipeline transportation systems Code is one of several sections of The American Society of Mechanical Engineers Code for Pressure Piping, ASME B31, and it is the responsibility of the user of this Code to select the applicable Section. This Section is published as a separate document...
Publisher: ASME Publish Date: 2016 Pages: 102 Language: English Format: PDF Document Scope Rules for this Code Section have been developed considering the needs for applications that include piping and heat transfer components for refrigerants and secondary coolants.
Publisher: ASME
Publish Date: 2015
Pages: 30
Language: English
Format: PDF
Document Scope
This Standard covers the standardization of dimensions
of welded and seamless wrought steel pipe for
high or low temperatures and pressures.
The word pipe is used, as distinguished from tube, to
apply to tubular products of dimensions commonly used
for pipeline and piping...
This Code covers rules for construction of power boilers, electric boilers, miniature boilers, high-temperature water boilers, heat recovery steam generators, solar receiver steam generators, certain fired pressure vessels, and liquid phase thermal fluid heaters8 to be used in stationary service and includes those power boilers used in locomotive, portable, and traction service....
This Section is a “Service Section” to the other BPVC Sections, providing material specifications for ferrous materials adequate for safety in the field of pressure equipment. These specifications contain requirements for chemical and mechanical properties, heat treatment, manufacture, heat and product analyses, and methods of testing. They are designated by SA numbers and are...
This standard identifies various information necessary for communication between a purchaser and a supplier of welding consumables. This standard, together with an AWS, ISO, or other recognized welding consumable standard, provides a method for preparing those specific details needed for welding consumable procurement which consist of the following: a) the welding consumable...
The goal of this Guideline is to assist the users of Section II, Part D in locating materials in stress tables (Tables 1A, 1B, 2A, 2B, 3, 4, 5A, and 5B), tables of mechanical properties (Tables U, U‐2, and Y‐1), and tables of physical properties (Tables TE-1 through TE-5, TCD, TM-1 through TM-5, and PRD). This Guideline defines the logic used to place materials within these tables.
The rules of Part HG apply to steam heating boilers, hot water heating boilers, hot water supply boilers, and to appurtenances thereto. They shall be used in conjunction with the specific requirements in Part HF (boilers of wrought materials), Part HC (cast iron boilers), and Part HA (cast aluminum boilers), as applicable. The Foreword provides the basis for these rules. Part HG...
The purpose of these recommended guidelines is to promote safety in the use of steam heating, hot water heating, and hot water supply boilers that are directly fired with oil, gas, electricity, coal, or other solid and liquid fuels. These guidelines are intended for use by those directly responsible for operating and maintaining heating and hot water supply boilers. These...
The primary function of a boiler is to generate steam. This is done by applying heat to the water in the boiler. The heat can be generated by electrical means or by combustion, i.e., burning fuel in a furnace. Electric boilers are discussed in Article 301. In the fuel-burning method, the heat generated by combustion is conducted through the metal of the boiler or boiler tubes to...
The rules of this Division constitute requirements for the design, construction, inspection, and overpressure protection of metallic pressure vessels with design pressures generally above 10 ksi (70 MPa). However, it is not the intent of this Division to establish maximum pressure limits for either Section VIII, Division 1 or 2, nor minimum pressure limits for this Division....
(a) Section X establishes the requirements for the fabrication of fiber‐reinforced thermosetting plastic pressure vessels for general service, sets limitations on the permissible service conditions, and defines the types of vessels to which these rules are not applicable. (b) To assure that vessels fabricated according to these rules will be capable of safely withstanding the...
The rules of this Section constitute requirements for construction and continued service of pressure vessels for the transportation of dangerous goods via highway, rail, air, or water. Construction is an all‐inclusive term comprising materials, design, fabrication, examination, inspection, testing, certification, and over‐pressure protection. Continued service is an all‐inclusive...
[/URL][/img]
Publisher: ASME
Publish Date: 2012
Pages: 520
Language: English
ISBN: 9780791868539
Establishes the requirements for preservice and inservice testing and examination of certain components to assess their operational readiness in light-water reactor power plants. It identifies the components subject to test or examination, responsibilities, methods,...
Publisher: ASME.
Publish Date: 2015 .
Pages: 244.
Language: English.
Format: PDF.
Document Scope .
This Standard provides methods for repair of equipment.
and piping within the scope of ASME Pressure.
Technology Codes and Standards1 after they have been.
placed in service. These repair methods include relevant.
design, fabrication, examination, and testing practices....
Publisher: ASME. Publish Date: 2015. Pages: 16. Language: English. Format: PDF. APPLICATION Of this supplement . (This is a special Supplement to the ASME pcc-2–2015 Standard.). The ASME pcc standards Committee opened a technical revision in 2010 to address repair. welding considerations for pressure vessels made from Cr–Mo steels in refinery, petrochemical, power generation,...
Publisher: ASNT. Publish Date: 2015 . Pages: 47. Language: English. Format: PDF. Сборник брошюр по методам NDT Американского общества. Краткое описание содержания и назначение каждой книги. Адреса и стоимость. Collection of publications on the American Society of NDT methods. A brief description of the content and purpose of each book. Addresses and cost.
Publisher: ASTM
Publish Date: 2014
Pages: 9
Language: English
Format: PDF
Document Scope
1.1 This specification covers two grades of electricresistance-
welded steel pipe in NPS 2 to NPS 30 [DN 50 to DN
750] inclusive, with nominal (average) wall thickness up to
0.500 in. [12.70 mm], inclusive, and in nominal sizes NPS 3⁄4
to NPS 5 [DN 20 to DN 125] inclusive with...
Publisher: ASTM Publish Date: 2015 Pages: 6 Language: English Book of Standards Volume: 01.01 Abstract This specification covers five grades of electric-fusion(arc)-welded straight-seam or helical steel pipe including pipe of NPS 4 and over. The required chemical composition, tensile requirements of the steel, and the tensile requirements of the production welds are presented....
Publisher: ASTM
Publish Date: 2015
Pages: 14
Language: English
ISBN: N/A
Abstract
This specification covers seamless ferritic and austenitic steel boiler, superheater, and heat-exchanger tubes. Grades containing the letter H in their designation have requirements different from those of similar grades not containing the letter H. These different requirements provide...