The Institute of Electrical and Electronics Engineers, Inc. 1996—287 p. This recommended practice serves as an engineering guide for use in electrical design for energy conservation. It provides a standard design practice to assist engineers in evaluating electrical options from an energy standpoint. It establishes engineering techniques and procedures to allow efficiency...
The Institute of Electrical and Electronics Engineers, Inc. 2000—75 p. The protection of power transformers is covered; various electrical protection schemes are explored; and guidelines are given for the application of these schemes to transformers. Alternative detection methods including mechanical, thermal, and gas analysis are discussed.
IEEE, 1995. — 30 p. — ISBN 1-55937-522-1. The characteristics of the various battery energy systems available are described so that users can select the system best suited to their requirements. This guide also describes how the rectifier and the inverter components of the uninterruptible power system (UPS) can relate to the selection of the battery system.
IEEE, 2014. — 30 p. The sizing of nickel-cadmium batteries used in standby operation for stationary applications is discussed in this recommended practice.
IEEE, 2020. — 67 p. Methods for defining the DC load and for sizing a lead-acid battery to supply that load for stationary battery applications in float service are described in this recommended practice. Some factors relating to cell selection are provided for consideration. Installation, maintenance, qualification, testing procedures, and consideration of battery types other...
The Institute of Electrical and Electronics Engineers, Inc., 2017. — 163 p. This recommended practice covers the protection of motors used in industrial and commercial power systems.It is likely to be of greatest value to the power-oriented engineer with limited experience in the area of protection and control. It can also be an aid to all engineers responsible for the...
Approved 7 December 2011 IEEE-SA Standards Board. — Revision of IEEE Std C37.118-2005. — New York: The Institute of Electrical and Electronics Engineers, 2011. — 53 p. Status: Valid A method for real-time exchange of synchronized phasor measurement data between power system equipment is defined. This standard specifies messaging that can be used with any suitable communication...
Copyright 2000 by the Institute of Electrical and Electronics Engineers, Inc. — 112 p. This introduction is not part of IEEE Std C37.113-1999, IEEE Guide for Protective Relay Applications to Transmission Lines. The art and science of the protective relaying of transmission lines has evolved over many years. This newly developed guide is an effort to compile information on the...
Developed by: PE/PSCC - Power System Communications and Cybersecurity Approved: 7 November 2019 Published: 21 January 2020 A cryptographic protocol to provide integrity with optional confidentiality for cyber security of substation serial links is defined in this standard. It does not address specific applications or hardware implementations and is independent of the underlying...
The Institute of Electrical and Electronics Engineers, Inc. - United States of America. - Published 21 July 2017. - 23 pages. This standard describes the interconnection details for N 64 kbps, where N = 1, 2 12, connections of teleprotection equipment to digital multiplexers using optical fiber. Requirements for both physical connection and the communications timing are also...
The Institute of Electrical and Electronics Engineers (IEEE), IEEE Computer Society. Revision of IEEE Std 754-2008. Approved 13 June 2019. 84 р. This standard specifies formats and methods for floating-point arithmetic in computer systems — standard and extended functions with single, double, extended, and extendable precision — and recommends formats for data interchange....
The Institute of Electrical and Electronics Engineers (IEEE), IEEE Computer Society. Revision of IEEE Std 754-2008. Approved 13 June 2019. 84 р. This standard specifies formats and methods for floating-point arithmetic in computer systems — standard and extended functions with single, double, extended, and extendable precision — and recommends formats for data interchange....
IEEE Std 830-1998(R2009) (Revision of IEEE Std 830-1993) IEEE Recommended Practice for Software Requirements Specifications Sponsor Software Engineering Standards Committee of the IEEE Computer Society Reaffirmed 9 December 2009 Approved 25 June 1998 IEEE-SA Standards Board Abstract: The content and qualities of a good software requirements specification (SRS) are described and...
IEEE Std 1233, 1998 Edition (Includes IEEE Std 1233-1996 and IEEE Std 1233a-1998) IEEE Guide for Developing System Requirements Specifications Sponsor Software Engineering Standards Committee of the IEEE Computer Society IEEE Std 1233-1996 Approved 17 April 1996 IEEE Std 1233a-1998 Approved 8 December 1998 by the IEEE-SA Standards Board Abstract: Guidance for the development of...
This document describes near-field test practices for the measurement of antenna properties. It provides information on developments in near-field measurements that have occurred since the writing of IEEE Std 149-1979 (IEEE Standard Test Procedures for Antennas). This document recommends near-field measurement practices for the three principal geometries: cylindrical, planar,...
IEEE Std 829-2008 (Revision of IEEE Std 829-1998) IEEE Standard for Software and System Test Documentation Sponsor Software & Systems Engineering Standards Committee of the IEEE Computer Society Approved 27 March 2008 IEEE-SA Standards Board Abstract: Test processes determine whether the development products of a given activity conform to the requirements of that activity and...
IEEE Std 1012-1998 (Revision of IEEE Std 1012-1986) IEEE Standard for Software Verification and Validation Sponsor Software and Systems Engineering Standards Committee of the IEEE Computer Society Approved 9 March 1998 IEEE-SA Standards Board Abstract: Software verification and calidation (V&V) processes, which determine whether development products of a given activity conform...
IEEE Std 1012-2016 (Revision of IEEE Std 1012-2012/ Incorporates IEEE Std 1012-2016/Cor1-2017) IEEE Standard for System, Software, and Hardware Verification and Validation Sponsor Software and Systems Engineering Standards Committee of the IEEE Computer Society Approved 28 September 2017 IEEE-SA Standards Board Abstract: Verification and validation (V&V) processes are used to...
IEEE 1008-1987 . Software unit testing is a process that includes the performance of test planning, the development of a test set, and the measurement of a test unit against its requirement. measuring entails the use of sample data to exercise the unit and the comparison of the unit’s actual behavior with its required behavior as specified in the unit’s requirement...
IEEE C37.111-1991 - IEEE Standard Common Format for Transient Data Exchange (COMTRADE) for Power Systems . Status: Superseded. Superseded by: C37.111-2013. Date of Publication: 1991. Electronic ISBN: 0-7381-1884-2. INSPEC Accession Number: 4054701. DOI: 10.1109/IEEESTD.1991.101025. ICS Code: 35.240.50 - IT applications in industry. Persistent Link:...
60255-118-1-2018 - IEEE/IEC International Standard - Measuring relays and protection equipment - Part 118-1: Synchrophasor for power systems - Measurements, 78p IEEE Power & Energy Society, IEC Date of Publication: 19 Dec. 2018 Electronic ISBN: 978-1-5044-5361-5 DOI: 10.1109/IEEESTD.2018.8577045 ICS Code: 17.220.20 - Measurement of electrical and magnetic quantities Persistent...