ASTM, 2004. — 3 p. This guide contains good practices for the selection, training, qualification, and professional development of personnel performing analysis, calibration, physical measurements, or data review using nondestructive assay equipment, methods, results, or techniques. The guide also covers NDA personnel involved with NDA equipment setup, selection, diagnosis,...
ASTM, 2009. — 5 p. This practice covers general requirements for the establishment and maintenance of a quality management system for agencies engaged in nondestructive testing (NDT).
ASTM, 2009. — 33 p. This standard defines the terminology used in the standards prepared by the E07 Committee on Nondestructive Testing. These nondestructive testing (NDT) methods include: acoustic emission, electromagnetic testing, gamma- and X-radiology, leak testing, liquid penetrant testing, magnetic particle testing, neutron radiology and gauging, ultrasonic testing, and...
ASTM, 2009. — 7 p. This guide establishes areas for review and provides a survey form that can be used in determining the competence of a nondestructive testing agency.
ASTM, 2007. — 9 p. This guide is intended to assist in the integration of ergonomic principles into the design and planning of new occupational systems from the earliest design stages through implementation. Doing so may reduce or eliminate the necessity for later redesign that could have been foreseen.
ASTM, 2009. — 4 p. This terminology describes and illustrates imperfections observed on whitewares and related products. For additional definitions of terms relating to whitewares and related products, refer to Terminology C 242. To observe these defects, examination shall be performed visually, with or without the aid of a dye penetrant, as described in Test Method C 949....
ASTM, 2007. — 11 p. The purpose of this guide is to present methods and techniques for the visual inspection of electrical protective rubber products. This guide also includes descriptions and photographs of irregularities found in these products.
ASTM, 2009. — 3 p. This practice is intended to serve as a guide for determining specific inspection requirements for marine surface preparation and coating application during new construction, major retrofit, or routine maintenance contracts.
ASTM, 2009. — 11 p. This document provides guidance on the implementation of risk assessment and risk control for Process Analytical Technology (PAT) processes within the pharmaceutical industry. Wherever possible, other appropriate standards on risk assessment/management have been referenced and acknowledged. Where practical, further details of methods and additional...
ASTM, 2010. — 6 p. The purpose of this guide is to establish a framework and context for process understanding for pharmaceutical manufacturing using quality by design (QbD) (Juran, 1992;2 FDA/ICH Q8). The framework is applicable to both active pharmaceutical ingredient (API) and to drug product (DP) manufacturing. High (detailed) level process understanding can be used to...
ASTM International, 2006. — 11 p. This guide identifies factors relevant to the quality of language translation services for each phase of a translation project. The guide is intended for use by all stakeholders, with varying levels of knowledge in the field of translation.
American Society for Testing and Materials, 1999. – 5 p. This guide describes the steps required to conduct a complete repeatability and reproducibility (RR) study on nondestructive test equipment. This guide is a manual (use of calculator) method. Other methods may utilize the application of computer driven software.
ASTM International, 2011. — 26 p. This guide presents terminology, concepts, and selected methods and formulas useful for measurement systems analysis (MSA). Measurement systems analysis may be broadly described as a body of theory and methodology that applies to the non-destructive measurement of the physical properties of manufactured objects.
ASTM International, 2010. — 25 p. This guide presents terminology, concepts, and selected methods and formulas useful for measurement systems analysis (MSA). Measurement systems analysis may be broadly described as a body of theory and methodology that applies to the non-destructive measurement of the physical properties of manufactured objects.
ASTM International, 2006. — 74 p. This practice consists of three annexes: hull structure, outfitting, and coating. The subject of these annexes was selected for several reasons. Other commercial shipbuilding nations already have in place widely recognized standards of expectations in these areas. These constitute the most significant areas where workmanship is a critical...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2015. Published December 2015. Last previous edition approved in 2008 as D5162 – 08. 5 p. This practice covers procedures for determining discontinuities (a flaw, void, crack, thin spot, foreign inclusion, or contamination in the coating film that significantly lowers the dielectric strength of...
Current edition approved Aug. 15, 2020. Published September 2020. Originally approved in 1993. Last previous edition approved in 2014 as E1237 – 93 (2014). This standard is issued under the fixed designation E l237; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in...
ASTM International. — 20 p. Adopted January 15 1992. Reapproved April 15 2014. Superseded by ASTM E251-20a. This standard is issued under the fixed designation B25I; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A...
Current edition approved June 1, 2020. Published August 2020. Originally approved in 1964. Last previous edition approved in 2014 as E25I - 9 2 (2014). This standard is issuod under the fixed designation B25I; the number immediately following the designation indicates tho year of original adoption or, in the case of revision, the year of last revision. A number in parentheses...
American Society for Testing and Materials (ASTM). Current edition approved Feb. 1, 2017. Published March 2017. Originally approved in 1974. Last previous edition approved in 2009 as D3359 – 09ɛ2. 9 p. These test methods cover procedures for assessing the adhesion of relatively ductile coating films to metallic substrates by applying and removing pressure-sensitive tape over...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2011. Published June 2011. Originally approved in 1974. Last previous edition approved in 2005 as D3363 – 05. 3 p. NOTES: Figure 1 was corrected editorially in August 2011. Figure 2 and Section 7 were corrected editorially in March 2012. This test method covers a procedure for rapid, inexpensive...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2014. Published January 2015. Originally approved in 1981. Last previous edition approved in 2010 as D4060 – 10. 5 p. This test method covers the determination of the resistance of organic coatings to abrasion produced by the Taber Abraser on coatings applied to a plane, rigid surface, such as a...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2013. Published July 2013. Originally approved in 1982. Last previous edition approved in 2007 as D4138 – 07a. 6 p. This practice describes the measurement of dry film thickness of coating films by microscopic observation of precision angular cuts in the coating film. Use of these procedures may...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 25, 1987. Published November 1987. Originally published as G 62 – 79. Last previous edition G 62 – 85. 4 p. These test methods cover the apparatus and procedure for detecting holidays in pipeline type coatings. Method A is designed to detect holidays such as pinholes and voids in thin-film...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2011. Published August 2011. Originally approved in 1985. Last previous edition approved in 2009 as G85–09. 14 p. This practice covers and sets forth conditions for five modifications in salt spray (fog) testing for specification purposes. These are in chronological order of their development:...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 25, 1987. Published November 1987. 4 p. This test method covers accelerated procedures for simultaneously determining comparative characteristics of coating systems applied to steep pipe exterior for the purpose of preventing or mitigating corrosion that may occur in underground service where the...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2014. Published February 2015. Originally approved in 1959. Last previous edition approved in 2009 as D1640 – 03 (2009). 4 p. These test methods can be used to determine the various stages and rates of drying, curing, and film formation of organic coatings for comparing types of coatings,...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2012. Published November 2012. Originally approved in 1945. Last previous edition approved in 2007 as D823 – 95 (2007). 8 p. Five practices are given for preparing films of uniform thickness of coatings on test panels. These practices are: Practice A—Automatic Spray Machine Application Practice...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2009. Published July 2009. Originally approved in 1943. Last previous edition approved in 2002 as D714–02. 6 p. This test method employs photographic reference standards to evaluate the degree of blistering that may develop when paint systems are subjected to conditions which will cause...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2012. Published November 2012. Originally approved in 1941. Last previous edition approved in 2008 as D610 – 08. 6 p. This practice covers the evaluation of the degree of rusting on painted steel surfaces. The visual examples which depict the percentage of rusting given in the written...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2013. Published December 2013. Originally approved in 1939. Last previous edition approved in 2008 as D522 – 93a (2008). 4 p. These test methods cover the determination of the resistance to cracking (flexibility) of attached organic coatings on substrates of sheet metal or rubber-type materials....